wuybx001 2010-11-8 18:59
thanks very much
fung1122 2010-11-8 19:04
*** 作者被禁止或刪除 內容自動屏蔽 ***
ak死神 2010-11-8 19:17
thankSSSSSSSSSSS
hk128m 2010-11-8 19:22
:funk: :funk: :funk: :funk:
lipper2 2010-11-8 21:46
回復 1# 的帖子
thank you for share
holymask 2010-11-8 21:46
thank you for your sharing!
turbo_him 2010-11-8 21:50
Thanks for sharing~!
cacwkh 2010-11-8 21:50
thx for sharing
dummytemp 2010-11-8 22:19
thanks a lot
lewis_laisulung 2010-11-8 22:24
55555555555555555
vrf 2010-11-8 22:29
thanks for sharing~
Photograph 2010-11-8 22:56
let me see how to 走光
Photograph 2010-11-8 22:57
Very nice picture, brothers!!!
p0o0iiuu 2010-11-8 23:06
ddfggdfgdfgdfgd
zenga 2010-11-8 23:29
多謝版主分享
don 2010-11-8 23:31
thanks for sharing
erliklik 2010-11-8 23:58
Thank you very very much!!!
jaysean 2010-11-9 00:02
:loveliness:
siuraye 2010-11-9 00:23
Thanks for share.
ttpoint 2010-11-9 01:20
looks very interesting.
wmahjx 2010-11-9 01:39
謝謝樓主:loveliness:
jaijai_ray 2010-11-9 01:45
22222222222222
jaijai_ray 2010-11-9 01:47
嘩...佢著左兩對C ar~~~~~~~~~~
huisimon 2010-11-9 01:51
very good............
古影134679001 2010-11-9 02:28
唔該樓主, 一定要支持.
QAZZAQ77 2010-11-9 02:42
.............
*** 作者被禁止或刪除 內容自動屏蔽 ***
sk2sk2 2010-11-9 03:01
thx for sharing
ryan1986 2010-11-9 03:32
:verygood: :verygood:
desmosedici 2010-11-9 03:41
:funk: :funk: :funk: :funk: :funk: :funk:
joehazard0 2010-11-9 03:47
:loveliness: :loveliness: :loveliness:
tsubame 2010-11-9 05:37
*** 作者被禁止或刪除 內容自動屏蔽 ***
FV8551 2010-11-9 06:55
thx~~~~~~~~~~~~~~~~~~
quantum 2010-11-9 07:07
thanks for your sharing~
clipper 2010-11-9 07:40
1323232323232323232323232323232323232323232323232323232323232
nanakogood 2010-11-9 07:50
Thank you very much!
NoA__Sunde 2010-11-9 08:30
thanks a lot~
348 2010-11-9 08:36
thx your share
YUIOPA 2010-11-9 08:44
thx for sharing
dali7419 2010-11-9 11:06
谢谢分享~~~~~~~~~
kent616 2010-11-9 11:17
yeh yeh thanks thanks
why2000 2010-11-9 11:26
thanks for sharing
tonycai121 2010-11-9 14:09
thanks very much
aavaavaav 2010-11-9 14:18
（1）将所有的动刀全部装在转子上，然后用紧固螺栓
[font=仿宋_GB2312][size=18pt]（1）将所有的动刀全部装在转子上，然后用紧固螺栓[/size][/font]
[font=仿宋_GB2312][size=18pt]轻轻压紧。[/size][/font]
[font=仿宋_GB2312][size=18pt]（2）装上底层定刀，使其尽量往后退，用紧固螺栓轻[/size][/font]
[font=仿宋_GB2312][size=18pt]轻夹紧。以定刀为基准使动刀和定刀之间的间隙用顶[/size][/font]
[font=仿宋_GB2312][size=18pt]刀螺钉调整在0.3-0.5mm范围内，其余动刀也以此定[/size][/font]
[font=仿宋_GB2312][size=18pt]刀为基准调整刀隙，使之在0.3-0.5mm范围内。[/size][/font]
[font=仿宋_GB2312][size=18pt]（3）将所有的动刀和定刀压紧后，再调整顶刀螺钉，使所有的刀具顶紧即可。[/size][/font]
9555 2010-11-9 14:38
thank for sharing.
chingx9 2010-11-9 14:43
thanks for sharing
hktigerwoods 2010-11-9 14:46
:verygood: :verygood: :verygood: :verygood: :verygood: :verygood: :verygood:
mrichboss 2010-11-9 14:52
:victory: :victory: :victory: :victory: :victory: :victory:
himawari 2010-11-9 15:11
see see see see see see see see see see see see see see see see
king999920 2010-11-9 15:16
好野一定要支持~~~~~~~~~~~~~~~~~~
sexyhkboy15 2010-11-9 15:17
:verygood: :verygood: :verygood: