香港 Xocat Forum 討論區 - Powered by Discuz! Board

標題: [疑難] window內置的防火埸沒有啟動, [打印本頁]

作者: ODO3033 時間: 2006-8-17 12:18 標題: window內置的防火埸沒有啟動,

每次開機, window內置的防火埸也沒有啟動, 我並沒有打開norton的防火埸, 不知有無兄弟可幫忙呢

作者: mnywong 時間: 2006-8-17 18:15

引用:

原帖由 ODO3033 於 2006-8-17 12:18 PM 發表
每次開機, window內置的防火埸也沒有啟動, 我並沒有打開norton的防火埸, 不知有無兄弟可幫忙呢

你用Winodws XP ?

作者: mnywong 時間: 2006-8-17 18:19

引用:

原帖由 mnywong 於 2006-8-17 06:15 PM 發表

你用Winodws XP ?

你係控制台 -> 防火牆有無開到啊.

作者: mnywong 時間: 2006-8-17 18:24

引用:

原帖由 mnywong 於 2006-8-17 06:19 PM 發表

你係控制台 -> 防火牆有無開到啊.

or you can do the following:

1. Click Start, click Run, type Firewall.cpl, and then click OK.
2. On the General tab, click Off (not recommended), and then click OK.

作者: ODO3033 時間: 2006-8-18 07:38

I enable it every time, after I turn off the computer, and turn it on again, the firewall is not enabled.

作者: mnywong 時間: 2006-8-18 10:56

引用:

原帖由 ODO3033 於 2006-8-18 07:38 AM 發表
I enable it every time, after I turn off the computer, and turn it on again, the firewall is not enabled.

Pls check the following value from registry:

HKLM\SYSTEM\CurrentControlSet\Services\SharedAccess\Parameters\FirewallPolicy\StandardProfile\EnableFirewall

1 = Enable
0 = disable

Pls be reminded that to close all application and backup your registry before you make any changes on it.

作者: ODO3033 時間: 2006-8-24 10:36 標題: 回復 #6 mnywong 的帖子

thanks will give it a try.

作者: 3033cat 時間: 2006-8-24 21:25

If you have SP2 the fire wall mustbe open auto.

作者: 焦器勃勃 時間: 2006-8-26 08:33

引用:

原帖由 mnywong 於 2006-8-18 10:56 AM 發表

Pls check the following value from registry:

HKLM\SYSTEM\CurrentControlSet\Services\SharedAccess\Parameters\FirewallPolicy\StandardProfile\EnableFirewall

1 = Enable
0 = disable

Pls be r ...

Pls advise how to Check the "registry" & obatin the following information ?? Any software that I need to EDIT the content (e.g. change the value 0 or 1 for enable or disable )

HKLM\SYSTEM\CurrentControlSet\Services\SharedAccess\Parameters\FirewallPolicy\StandardProfile\EnableFirewall

1 = Enable
0 = disable

作者: mnywong 時間: 2006-8-31 16:54

引用:

原帖由 焦器勃勃 於 2006-8-26 08:33 AM 發表

Pls advise how to Check the "registry" & obatin the following information ?? Any software that I need to EDIT the content (e.g. change the value 0 or 1 for enable or disab ...

Click Start => Run => Type "regedt32", the registry editor will be opened. Browse through it like a Winodws Explorer. Hope this help !

歡迎光臨香港 Xocat Forum 討論區 (http://p.xocat.com/p/)